Search results for: 'truth entrygard operator 20755'

Pella Casement Operator Cover

Right Hand Cover Shown

Truth Encore Dual Arm Operator for Low Profile windows.  Same as the Wi5010, but has a rectangular slide on the long arm instead of the standard models square slide.

The Split Arm Roto Operator has been around for the past 10-15 years.  The housing is 4-1/2" wide, and the linkage arm has an overall length of 4-3/8".  One of the most recognizable features of this mechanism is the female hex fitting for the handle.

Right Hand shown in the picture

Pella Casement Operator

Left Hand Shown

Casement Window Operator 9" Arm

Die cast housing with steel arm. The hole spacing of the window operator housing is 4-3/4" on the outside screws and 3-7/8" on the inside two screws. The arm is 9" from the roller to the center of the window operator housing. This operator uses a 5/16" spline operator, part #Ro169516.

Ro267 Right Hand
Ro268 Left Hand

Handing Diagram

The Andersen Perma-Shield Single Arm Operator is avialable in the Stone Color.  Use the Drop Down Menu to Confirm and the Handing you need.  If your window Lock is on the Left, Order the Left Hand.  Operator arm measures 9-3/8 inches.

This Older style Andersen Single Arm operator has an are that is 8-7/8 inches long.  The front two hole spacing is 3-1/8 inches.  Ships with handle.

Ashland Operator Cover measures 4 inches across.  We find the number US Patent Pending P-1080-100 on the Left Hand Covers and P-1080-200 on the Right Hand Covers.

The Fenestra Window Operator 4-1/4" was used between 1930 to 1970.  The operator features die cast metal construction with a steel arm.   The original version was made of cast bronze, which in today's market would be cost prohibitive.  This unit ships with handle and mounting screws.

Right Hand Operator shown in picture.

Handing Diagram

Replacement Hope's Window Operator.

Die cast construction with steel arm. The arm measures 9-1/2" long for the roller to the center of the housing.

Pella Casement Operator Cover

Right hand shown in Copperite

The Truth Encore Handle and Cover are used on the Encore Operators Wi5110 and Wi5010.  The flush design is ideal when you have curtains and blinds on your window.  The cover are constructed on Plastic and the Handles are die cast metal.  Use the drop down menu to figure out hand, the color is not correct by the handing is, select color and then hand.

Color Chart

Truth Part Numbers 12614 (Left Hand) and 12616 (Right Hand).

The Fenestra Window Operator 3-1/4" is a replica of a version made in the 1920's to 1950's. This version is made of a die cast material, that is then powder coated in an aluminum finish. If you want bronze color, your best bet is to purchase some bronze spray paint and paint them. Ships with mounting screws and handle.

Handing Diagram

The Andersen Perma-Shield Split Arm Operator is avialable in the Stone Color.  Use the Drop Down Menu to Confirm and the Handing you need.  If your window Lock is on the Left, Order the Left Hand.

Casement Window Operator 11" Arm

Die cast housing with steel arm. The hole spacing of the window operator housing is 4-3/4" on the outside screws and 3-7/8" on the inside two screws. The arm is 11" from the roller to the center of the window operator housing. This operator uses a 5/16" spline operator, part #Ro169516.

Pella Casement Window Operator

Left hand shown in picture

Casement Roto Operator

This Roto Casement Operator features a hole spacing of 3-1/2" on thee outside mouting holes and 1-7/8" on the two inside mouting holes.  The housing is contructed of die case metal that is electro-statically painted.   The housing is 5-1/2" wide.  The optional handle fits the 5/16" Hex Shaft.

Left Hand Shown in picture

Fenestra Window Operator 5-1/4

The arm is 9" long and the outside screw spacing is 5-1/4". The inside threaded holes are 4-1/4" apart. Die cast construction with steel arm. Ships with handle and mounting screws.

Handing Diagram

Roto Split Arm Operator Pin Up

The housing is 4-1/2" wide, and the linkage arm has an overall length of 4-3/8"

Left Hand shown in the picture

This GU Split Arm Operator replaces the original version which was plastic.  The new version is made of die cast metal and is much stronger that the original. Comes with handle.

Right Hand Shown

Truth 16.16 Sash Lock.

3" x 2-9/16" x 1", with 2-3/8" hole spacing

This sash lock has been discontinued. If you order this part, the 16.27 will be sent as a replacement. According to the factory, the Wi1627 will work as a replacement with any modification.

Used truth keeper # Wi20034

Truth Multi Point Locking System sash lock. The hole spacing on the lock is 3-7/16"

Left Hand Shown in Picture

Common numbers found on this lock is 31401 and 31402

Color Chart

Truth 24.89 Multi Point Locking System Sash Lock

31149 is stamped on the Right Hand Sash Lock

31369 is stamped on the Left Hand Sash Lock

Right Hand Shown in Picture

Color Chart

The Truth Hole Two Cam Handle 1-1/2" Offset has die cast construction with a powder coated painted finish. We find the numbers 45086 on the right hand handles, and 45085 on the left hand handles. Right Hand Shown on Website!

Color Chart

The Project In Truth Handle-1-1/2"- 1/2" Lock Up is a handle we have seen since the 1970's.  This window handle features a 1-1/2" hole spacing on centers with a 1/2" lock up dimension. The window handle is constructed of a die cast material that is then powder coated to the finish of your choice. We find it used on Project In or Thru Rail type Hopper windows.  We stock the Bronze color, but other colors are available, call for more information.

Right Hand handle shown in picture.

Angle Base 1-3/8" Window Handle Truth

Also known as the Truth 25.39, this handle is constructed of a die cast metal and powder coated to the desired color. The distance between the screws is 1-3/8" on center. The handle measures 3-3/4" long, base measures 2-1/8" long. The number found on the handle is 45086 for the Right Hand, and 45085 for the Left Hand. We also find U.S. Pat. # 4,930,820

Right Hand is shown in picture.

The Project In Truth Handle-1-1/2" -7/16" Lock Up is a handle we have seen since the 1970's.  This window handle features a 1-1/2" hole spacing on centers with a 7/16" lock up dimension. The window handle is constructed of a die cast material that is then powder coated to the finish of your choice.  It is used on Project In or Thru Rail Hopper style windows. We stock the Bronze color, but other colors are available, call for more information.

Right hand handle is shown in the picture.

The Truth Two Hole Cam Handle 1-1/2" W/Ring Pull is considered an In Line handle, because the mounting holes line up with the axis of rotation of the cam handle.  This is a very popular handle that has only been around since the 1970's.  It is die cast metal that is then powder coat painted.

Left Hand Shown in picture.

The Truth Two Hole Cam Handle 1-1/2" Inline has a die cast construction with a powder coated paint finish.  It features an 1-1/2" hole spacing.  We find the numbers 45086 on the right hand handles, and 45085 on the left hand handles.  This handle is very popular on aluminum framed commercial windows due to its low cost.

The handle shown in the picture is a Right Hand.

Color Chart

The Truth Hole Two Cam Handle 1-1/2" W Ring Pull Offset is considered an off set handle, because the mounting holes are off set  with the axis of rotation of the cam handle.  This is a very popular handle that has only been around since the 1970's.  It is die cast metal that is then powder coat painted.

Right Hand Shown in picture.

Truth part # 25.70.03.xxx

Two Hole 1-1/2" Window Handle

This window handle has a 1-1/2" hole spacing with a 5/16" lock up dimension. The handle also features a ring pull for elevated windows. Cast white bronze with a brushed nickel finish.

Right Hand Shown